黑色硅膠密封劑81158 、81173
Permatex Black Silicone Adhesive Sealant
泰揚黑色硅膠密封劑
Phone: 18930426792? Mobile: 021-67769720
Permatex Black Silicone Adhesive Sealant
泰揚黑色硅膠密封劑
是一種通用型、黑色、室溫硫化密封劑，可密封、粘合、修復、彌補玻璃、金屬、塑膠、紡織品、擋風條及vinyl tops。它防水性好，韌性高，可在任何垂直或水平表面上操作。該產品的工作溫度范圍在-59℃- 232℃之間。它的強密封性可抵抗水、油、老化、振動、油脂等帶來的影響。
包裝規格
型號 | 包裝規格 | 每箱數量 | 產品代號 |
81158 | 3盎司卡式管裝 | 12 | 66BR |
81173 | 11盎司卡桶 | 12 | 16C |
PRODUCT DESCRIPTION Permatex Black Silicone Adhesive Sealant ia a general purpose single component, room temperature vulcani zing(RTV) gasketing compound, designed for the seali ng of mechanical assemblies. Upon curing from the ex posure to moisture in the air, this non-sagging paste forms a tough, flexible, waterproof seal of silicone rub ber, which resists aging, weathering and thermal cycli ng without hardening, shrinking or cracking, Conforms to MIL-A-46106b, Type I. Permatex Black RTV Silicone Adhesive Sealant shall meet the requirements of the F. D.A."Code of Federal Regulations 21 CFR" concerning food contact applications if use in accordance with its Section 177.2600:"Rubber Articles Intended for Repea ted Use". PRODUCT BENEFITS ● Easy application ● Applied to horizontal or vertical surfaces ● Superior adhesion and flexibility ● Waterproofs ● Insulates ● Unaffected by vibration ● Non-flammable TYPICAL APPLICATIONS Permatex Black Silicone Adhesive Sealant is an excellent all-purpose adhesive/sealant for the following materials: ● Metal ● Glass ● Wood ● Plastic ● Silicone resin ● Vulcanized silicone rubber ● Ceramics ● Natural and synthetic fibers ● Painted surfaces DIRECTIONS FOR USE For Assembly 1.Remove all previous material from mating surfaces. Permatex Gasket Remover is recommended for most materials, not for plastics or painted surfaces. 2.For best results, clean and dry all surfaces with a resid ue-free solvent, such as Permatex Brake and Parts Cle aner. 3.Cut nozzle to desired bead size, 1/16 to 1/4 in diameter An 1/8 bead is usually sufficient for most applications. 4.Remove cap, puncture tube or cartridge seal and attach extension nozzle. 5.Apply a continuous and even bead of silicone to one surface, as shown below. 6.Assemble parts immediately while silicone is still wet. Secure or tighten as required, avoiding excessive squeeze-out 7.Re-torque will not be necessary after teh product has cured. For Cleanup 1.Allow excess material to extend beyond the extension nozzle or aerosol tip to cure, sealing and protecting the remaining product from moisture, For reuse, simply rem ove the cured product from the tip. 2.Remove uncured product from parts and hand-tools with a dry cloth, if skinned over , break film with a dry cloth to remove as much as possible, and remove the remaining material with Permatex Gasket Remover. 3.Clean hands with a dry cloth or Permatex Fast Orange hand cleaner. | PROPERTIES OF UNCURED MATERIAL Typical Value Chemical Type Acetoxy silicone rubber Appearance Black non-sag paste Odor Mild acetic Specific Gravity 1.07 Extrusion rate@25℃，(grams/min) >220 Flash Point ℃，℉ >93(>200) TYPICAL CURING PERFORMANCE Permatex Black Silicone Adhesive Sealant cures on expo sure to moisture in the air. The product dries tack free in 1 hour and fully cures in 24 hours, Cure times will vary with temperature, humidity and gap ,Note: The curing process can cause corrosion to some surfaces, for critical applications use the Ultra Series silicones. PERFORMANCE OF CURED MATERIAL After 7 days at 25℃(77℉），50% Relative Humidity Typical Values Hardness(Shore A) >20 Elongation, % >350 Tensile Strength ,N/MM2(psi) >1.5 (>218) Material will stretch 3.5 times its original length before breaking Amount of force required to break material TYPICAL ENVIRONMENTAL RESISTANCE Temperature Resistance Typical Values Continuous,℃(℉) -59 to 232 (-75 to 450) Intermittent,℃(℉) -59 to260 (-75 to 500) Chemical/Solvent Resistance The product retains effective properties in contact with au tomotive fluids, such as motor oil, transmission fluids, alcohol and antifreeze solutions. Note:Not recommended for parts in contact with gasoline. GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet,(MSDS). STORAGE Products shall be ideally stored in a cool, dry location in un opened containers at a temperature between 8 to 28 ℃(46 to 82℉) unless otherwise labeled. Optimal storage is at con tamination of unused product, do not return any material to its original container. NOTE The data contained herein are furnished for information only and are believed to be reliable. We can not assume responsi bility for the results obtained by others over whose methods we have no control. Permatex, Inc.specifically disclaims all warranties expressed or implied, including warranties of mer chantability or fitness for a paricular purpose, arising from sale or use of Loctite Corporation is products and disclaims any liability for consequential or incidental damages of any kind, including lost profits. This product may be covered by one or more United States or foreign patents or patent applications. |
●避免與皮膚及眼睛直接接觸，請于使用時戴上塑膠手套及安全護目鏡。
●若因接觸皮膚引起過敏及紅斑，請以肥皂及清水沖洗；若不慎觸碰到眼睛時，請立即以清水沖洗并就醫診查
●勿吞食、勿讓孩童取用。
●使用本材料的工作環境須通風良好，勿在密閉空間使用。
